NEC Wire Sizing
What Size Wire for an Electric Cooktop?
The breaker, copper and aluminum wire, and ground for a typical electric cooktop circuit, with the NEC basis and the nameplate caveats that actually decide it.
Electric Cooktop Circuit Spec
| Voltage | 240V |
| Breaker | 40A |
| Copper wire | #8 |
| Aluminum wire (75°C, SER or conduit) | #8 |
| Equipment ground (Cu) | #10 |
Cooktops range from 30A to 50A depending on the number and size of elements. A standard four-burner cooktop is commonly on a 40A circuit; size to the nameplate. Under the 2023 NEC (210.8(A)), a dwelling cooktop receptacle requires GFCI protection; this 2023 expansion is still being adopted, so verify your local edition. Wire sized at NEC Table 310.16 (copper lead at the 60°C column for NM-B); ground per NEC Table 250.122. The appliance nameplate lists the exact minimum circuit and maximum breaker; it always governs over a typical value.
Aluminum branch conductors are 75°C-rated AA-8000 alloy (SER cable, or XHHW-2 / THWN-2 in conduit); there is no 60°C aluminum NM-B, so the aluminum row uses the 75°C column. Where the terminations are rated 60°C only, size aluminum from the 60°C column instead (#6 here).
Adding this as a new load? Check whether your panel can handle it (the NEC 220.87 service check), or compare it against the breaker size by load chart.
Long Run? Size It Exactly
For a long run where voltage drop matters, or a nameplate that differs from the typical value, enter your exact load, distance, and conditions.
Frequently Asked Questions
What size wire do I need for an electric cooktop?
An electric cooktop typically uses a 40A / 240V circuit, which calls for #8 copper (or #8 aluminum) conductors and a #10 copper equipment ground per NEC Table 250.122. Cooktops range from 30A to 50A depending on the number and size of elements. A standard four-burner cooktop is commonly on a 40A circuit; size to the nameplate. Under the 2023 NEC (210.8(A)), a dwelling cooktop receptacle requires GFCI protection; this 2023 expansion is still being adopted, so verify your local edition.
What size breaker for an electric cooktop?
A 40A double-pole (240V) breaker. The #8 copper conductors are matched to that 40A rating. Do not oversize the breaker to a wire it does not protect: the breaker and the conductor go up together. Always confirm against the appliance nameplate, which lists the exact minimum circuit and maximum overcurrent device.
Can I use aluminum wire for an electric cooktop?
Yes. On the 75C column (the usual basis for aluminum), a 40A circuit needs #8 aluminum, versus #8 copper. Aluminum is common on larger circuits and services to save cost; apply antioxidant to the terminations, torque to the listed spec, and remember aluminum drops slightly more voltage on long runs.
What size breaker for a stovetop?
Same answer: stovetop is another name for an electric cooktop. It uses a 40A / 240V circuit with #8 copper wire and a #10 copper ground. Cooktops range from 30A to 50A depending on the number and size of elements. A standard four-burner cooktop is commonly on a 40A circuit; size to the nameplate. Under the 2023 NEC (210.8(A)), a dwelling cooktop receptacle requires GFCI protection; this 2023 expansion is still being adopted, so verify your local edition.
Wire Size for Other Appliances
Electric Dryer
#10 copper on a 30A / 240V circuit.
Electric Range
#6 copper on a 50A / 240V circuit.
Electric Wall Oven
#8 copper on a 40A / 240V circuit.
Electric Water Heater
#10 copper on a 30A / 240V circuit.
Hot Tub
#6 copper on a 50A / 240V circuit.
Dishwasher
#12 copper on a 20A / 120V circuit.
Garbage Disposal
#14 copper on a 15A / 120V circuit.
Built-In Microwave
#12 copper on a 20A / 120V circuit.
Refrigerator
#12 copper on a 20A / 120V circuit.
Freezer
#12 copper on a 20A / 120V circuit.
Garage Door Opener
#12 copper on a 20A / 120V circuit.
Wire Size Calculator
Full NEC 310.16 sizing for any load, distance, and conditions.