NEC Chapter 9 Conduit Fill

What Size Conduit for 8/2 Wire?

The smallest conduit for 8/2 (two #8 plus one #10 ground) in EMT, PVC, RMC, and IMC at the NEC fill limit, with the area math and the calculator for any other mix.

Quick answer: 8/2 wire (two #8 plus one #10 ground, 3 conductors = 0.0943 sq in) needs 1/2″ EMT or 1/2″ PVC at the NEC 40% fill limit. Used for a 40-50A 240V load such as a wall oven.

Minimum Conduit for 8/2 by Type

Smallest conduit that holds 8/2 (two #8 plus one #10 ground) at the NEC 40% fill limit

Swipe the table sideways to see the rest of its columns. →

Conduit TypeMinimum Size
EMT1/2"
Schedule 40 PVC1/2"
RMC1/2"
IMC1/2"

3 THHN conductors totaling 0.0943 sq in (NEC Chapter 9 Table 5). With three or more conductors the fill limit is 40% (Table 1), so the required internal area is 0.0943 ÷ 0.40 = 0.236 sq in, and each type's smallest trade size at or above that is shown.


Different Conductors? Calculate It

For a different wire mix, insulation type, or added conductors, enter your exact pull for the precise fill percentage and the smallest compliant conduit. The calculator opens on this page's 8/2 THHN set in 1/2″ EMT.

31.0%
conduit fill
NEC PASSThreshold: 40% (3+ conductors)

Within fill: 31.0% of 40%

#8 AWG THHN × 20.0732 sq in
#10 AWG THHN × 10.0211 sq in
Total conductor area0.0943 sq in
Conduit area (1/2" EMT)0.3040 sq in
Remaining space0.0273 sq in
Show the math
  1. GIVENConduit: 1/2" EMT; 3 conductors
  2. TABLE#8 AWG THHN: 0.0366 sq in each × 2 = 0.0732 sq inNEC Chapter 9 Table 5
  3. TABLE#10 AWG THHN: 0.0211 sq in each × 1 = 0.0211 sq inNEC Chapter 9 Table 5
  4. MATHTotal conductor area: 0.0943 sq inNEC Chapter 9 Table 5
  5. TABLE1/2" EMT total area: 0.3040 sq inNEC Chapter 9 Table 4
  6. TABLEFill limit for 3+ conductors: 40%, an allowable area of 0.1216 sq inNEC Chapter 9 Table 1
  7. MATHFill = 0.0943 / 0.3040 × 100 = 31.0%NEC Chapter 9 Table 1
  8. RESULTFill: 31.0% of a 40% limitNEC Ch. 9 Tables 1, 4, 5
  9. RESULTStatus: NEC PASSNEC Ch. 9 Tables 1, 4, 5
Where this number comes fromIntry Verified
Calculated from
NEC Ch. 9 Tables 1, 4, 5. Computed from NEC Chapter 9 Table 1 (fill percent), Table 4 (conduit area) and Table 5 (conductor area), with Note 7's round-up at a decimal of 0.8 or more for conductors all of one size. See the full receipt ↓
Run with
  • Conduit1/2" EMT
  • Conductors2 #8 AWG THHN, 1 #10 AWG THHN
  • Fill limit40%
Checked
Every figure an Intry calculator computes comes from a locked source module, not hand-typed. 35,938 automated checks, one suite for the whole site rather than a per-tool count, re-derive the numbers before each deploy from the tables this site holds, read from the cited NEC section. This is our own deterministic gate, not a third-party audit.
Final say
Your AHJ and local amendments have final say. Confirm before rough-in.
What Intry Verified means

Intry Verified · NEC 2023 · Build 525536D · 2026-11-13

Bend this EMT →
31.0% fillNEC PASS

Frequently Asked Questions

What size conduit do I need for 8/2 wire?

8/2 wire pulled as individual THHN conductors (two #8 plus one #10 ground) needs 1/2 inch EMT, or 1/2 inch Schedule 40 PVC, at the NEC 40% fill limit. The 3 conductors total 0.0943 square inches (NEC Chapter 9 Table 5); with three or more conductors the raceway may be filled to 40%, so the smallest conduit whose 40% area covers 0.0943 sq in is 1/2 inch EMT.

What is the minimum EMT size for 8/2?

1/2 inch EMT. Its internal area at 40% fill exceeds the 0.0943 sq in that 8/2 (two #8 plus one #10 ground) occupies. Going one trade size down would exceed 40% and violate NEC Chapter 9 Table 1. If you are running RMC use 1/2 inch; IMC and PVC each have their own internal area, shown in the table above.

Does the ground wire count for conduit fill on 8/2?

Yes. Every conductor in the raceway counts for fill, including the equipment grounding conductor (NEC Chapter 9 Table 1). That is why 8/2 is figured here as two #8 plus one #10 ground: the 3 conductors together, not just the current-carrying ones. Leaving the ground out of the count is a conduit-fill mistake.

Can I use 8/2 as NM cable (Romex) in conduit instead?

If you sleeve an intact 8/2 NM cable (Romex) rather than pulling individual THHN, the fill is figured differently: a single cable is treated at the 53% one-conductor limit using the cable's actual cross-sectional area (NEC Chapter 9, Note 9), which can need a larger conduit than individual THHN. The 1/2 inch answer above assumes individual THHN conductors.


Conduit Size for Other Wire

Conduit sized. Will the wire reach?

Getting 8/2 in the pipe is one thing. Confirm the gauge holds up over the run length with the voltage drop calculator before you pull.